8. Control Stick Boot (2)
9. Elevator Trim Bracket (2)
10. Elevator Trim Wheel (2)
11. Door Handle Bracket (1)
12. Rear Rudder Pedal Mounting Bracket

1. Front Floor Section
2. Rear Floor Section
3. Left Front Former Covers
4. Rear Front Former Covers
5. Rear Former Covers (4)
6. Battery
7. Battery Box Bottom
8. Battery Box Top
9. Relay Shelf Below Dash
10. Cover for Center Windshield Former
11. Dash
12. Dash Hood
13. The Light Dimmer and Bracket (2)
14. Fuel Selector Valve
15. Upper Compass on windshield brace
16. Rudder Pedals (4)
17. Map Cases (2)
18. Gas Gauges (2)
19. Door Frame
20. Misc. Longeron Covers 4 lg, 4 sm.

1. 3 Ft. Wire for Lights
2. 3 Ft. Alum. Wire for Toggle Switches
3. 3 12" Pieces 1/8 Alum. Rod
4. 3 12" Pieces of 3/32 Alum. Rod
5. 9" of 3/8" Plastic Tubing
6. 1" of 3/4" Plastic Tubing
7. 1 Plywood Piece for Fuel Gauge 1/8" x 2 x 4
8. Dash Gauges
9. Plastic for Dash Gauges
10. Computer Disc with Pictures
11. 6 Large Pins
12. 6" of 1/8" Alum. Tubing
13. 2" of 3/32" Plastic Tubing
14. 2" of 3/8" Round Plastic Solid
15. Front Seat Frame
16. Rear Seat Frame
17. Green Denim 8x30" for Seat Covers
18. Vinyl Cloth 12 x 30"
19. 4 Seat Rails, 6 1/2" Long
20. 6" of 3/8 Plastic Tubing for Front Rudder
Pedal Mounting Bracket
21. 6" long Black Cord
22. 1/4" Plastic Rod 3"
23. 3/8 Alum. Strip 4”
24. T-Pin

1. Air Vents (4)
2. Side Lights (3)
3. Throttle Quadrant (2)
4. Top of Control Stick (2)
5. Front Control Stick
6. Rear Control Stick
7. Ash Trays (2)

1. Front side of Former Wall
2. Rear side of Former Wall
3. Dash Panel
4. Two Side Panels
5. Dash Hood
6. Interior Window Molding (10)
7. Interior Wall Sections (6)
8. Seat Bottoms (7)
9. Seat Backs (7)
10. 4x7 Plastic Sheet (7)
11. Steps
12. Step Ends
13. Center Console
14. One Piece of Plastic, 12x12

1. Two Control Shafts
2. Two Steering Wheels

1. Felt, 10 x 30
2. Four Large Pins
3. Three 3/32 Alum. Tubing, 4" Lg
4. Decal Sheet
5. Computer disc

1. Floor ( 2 pcs)
2. Rear Wall
3. Right Side Wall
4. Left Side Wall
5. Front Dash
6. Rear Dash
7. Front Dash Hood
8. Rear Dash Hood
9. Front Right Console
10. Front Left Console
11. Rear Left Console
12. Front Center Dash
13. Left Side Panel between dash
14. and Side Console
15. Right Side Panel between dash
16. and Side Console
17. Cable Covers (2 pcs)
18. Rear Dash
19. Middle Dash

1. Two Seats in vacuform parts bag
2. Bottom Seat Cushion (2)
3. Parachute Pack (2)
4. Armour Plating (plastic pieces) (2) 3x7
5. Seat Rails (2 pcs)
6. Two Balsa Blocks for seat base
7. 3/32" Aluminum Tubing, 2 6" Pcs
8. Two Large Pins
9. 1/4" Plastic Rod, 1" Long
10. 1/16" Aluminum Rod, 6" Long
11. Resin Canopy Breaker (2 pcs)
12. 1/4" Foam Rubber, 6x6
13. 1/16" Black Elastic Chord 6" lg

1. 3/16" Alum Tubing, 6 long
2. 1/2 x 1/2 Hardwood Block, 1" Long
3. 6" of 1/8" Aluminum Rod
4. 3/16" Plastic Rod, 2" Long
5. 3/32" Aluminum Tubing, 6" long
6. 12 Large Pins
7. Computer Disc
8. .030 Plastic 4x6 three Pieces
9. One T-Pin

1. Compass
2. Front Control Stick Handle
3. Rear Control Stick Handle
4. Control Stick Bottoms (2)
5. Control Stick Middle (2)

1. Left Side
2. Right Side
3. Dash
4. Seat
5. Lower Dash
6. Armour Plating
7. Head Rest
8. Seat Brace
9. Two 3/16" x 4 1/2" Tubing
10. Four 7/32" x 3/4" Seat Bushings
11. Control Yoke
12. Control Column
13. 1/2" Round x 1/2" Long Plastic for Cover
14. 3/16" Round x 1" for Yoke Shaft

15. 6 Large Pins and 8 Small Pins
16. Computer Disc
17. Aluminum Wire for Toggle Switches
18. Dash Hood
19. Gunsight

1. Floor
2. Cockpit Rear Wall
3. Upper Deck
4. Left Side
5. Right Side
6. Dash
7. Lower Dash
8. Seat
9. Center Console between
10. Floor and dash
11. Dash Hood
12. Oxygen Pressure gauge
13. Stand by Magnetic Compass

1. Radio Control
2. Seat Brace
3. Armour Plate
4. Head Cushion
5. 4 Radio Boxes on Upper Deck
6. Steering Wheel
7. Control Column
8. Boot for Control Column
9. Gunsight with 4 Screws

1. Oxygen Hose
2. Tubing for Brace for Armour Plate
3. Tubing 7/32 x 12"
4. Tubing for Steering wheel Shaft 7/32 x 1"
5. Seat Bushings for Rail 1/4 x 1/2" Long (4 Pcs)
6. 1 Pkg Pins, 12 small and 2 lg. Pins)
7. Tubing for back of gauge for Oxygen Pressure Gauge

1. Dash
2. Dash Hood
3. Floor
4. Side Walls (2)
5. Rear Cockpit Wall
6. Throttle Quadrant Mount
7. Trim Box
8. Control Cable Cover
9. Seat
10. Rudders Pedals (2)
11. Map Case
12. Bomb Drop Mount
13. Lower Dash

1. Radio
2. Rudder Pedal Mount (2)
3. Cowl Flap Lever
4. Side Lights (2)
5. Fuel Tank Gauges (2)
6. Elevator Trim Knob
7. Rudder Trim Knob
8. Armour Plate
9. Oxygen Regulator
10. Dash Lights (3)

1. 2 Rail Top Mounts
2. 2 Rail Bottom Mounts
3. 2 Pieces 1/4" Tube x 6" Lg.
4. 4 Pieces 9/32" Alum.Tube,1" Lg.
5. Vacuform C Channel

1. Body
2. 2 Medium Pins
3. 1 Large Pin
4. 3 3/2" Alum. Tube, 4" long
5. 3/32" Alum. Rod, three 6" Pcs
6. 1" of 3/8" knurled Rod
7. 1" of 1/8" Plastic Rod

1. Main Body
2. 2x2 Plastic Lens
3. 6" of Black Chord
4. Gunsight Mount
5. Four 1/4" x 1 Screws

1. Rudder Control Front Mount
2. Rudder Control Rear Mount
3. Yoke Stick Bottom
4. Yoke Elevator Rod Attachment
5. Control Stick
6. Handgrip
7. Tail Wheel Release Box
8. 3/32" Plastic Rod, 1" Lg.
9. 6" of Silver Chord
10. 7" of 1/4" Alum. Tubing
11. 7" of 3/16" Alum. Tubing
12. Two 3/16" x 0 Screws

1. 1/2 Dowell
2. Resin Knob
3. 5" of 1/16" Alum. Rod
4. One Decal on decal sheet (not in this bag)
Flap Control

1. Base
2. Crank Arm
3. Crank Arm Channel
4. Large Pin

1. Body
2. 2 Large Pins
3. Two 3" Pieces of 1/16" Rod
4. 3" of 3/32" Alum. Tubing

1 Main Body
2 2 Large Pins
3 3/32" Tubing 3" Long

1. 1/8" chord for simulating wire harness,3'
2. 9" of Flex Hose, 3/16"
3. 1/8" Alum. Rod, 6" Lg.
4. Alum. Wire
5. Computer Disc
6. One T-Pin
7. 6" of 3/32" Alum. Rod
8. 1 Ft. of 20 gauge Wire
9. Balsa Block, 2x 3 x 3/8"
10. 6 x 6 Black Plastic
11. 24" of 1/16" Steel Cable
12. 1" of 5/32" Plastic Tube
13. 6" of Silver Chord

1. Pump Body
2. Pump Handle, 1/8" x 3 Alum. Tube
3. Boot
4. Large Pin

1. Floor
2. Left and Right Side Walls
3. Rear Wall
4. Dash
5. Dash Hood
6. Side Panel to right of Dash
7. Vent Control Box
8. Map Case

1. Main Body (Resin)
2. Tension Knob
3. 1/4" knurled Knob 1" Long
4. 6 Large Pins
5. 5/32" Alum. Tube 3" Long
6. 1/8" Alum. Tube, 3" Long
7. Mounting Plate, Plastic
8. 3/32" Rod,2 4" Pieces
9. Seat Pack
10. Top Seat Brace
11. 1/4" Alum. Tubing, 7" Long, 2 Pieces
12. Seat (Vacuform) in Main Bag
13. 1/16" Alum. Rod, 6" Long
14. Small Eye Screws (2)
15. 1/8" Elastic Strap, 24" Long
16. One Large Pin
17. 1/8" of Alum. Tube, 2" Long

1. Alum. Wire
2. Computer Disc
3. 2-T-Pins and Four Large Pins
4. Dark Cloth for Control Stick Boot 4x4
5. 1/4" Fuel Tube, 3" Long
6. 9" of 3/16 Flex Hose
7. 2 Ft. of heavy Black Cord
8. Light Brown Cloth for Headrest, 4x4
9. 1/16" Rod, 6" Long
10. 1/4" Balsa, 2x2"
11. 6" of 1/8 Rod
12. 2 Ft. of 22 Gauge Wire
13. 1/8" Plastic Rod, 2" Long
14. 1/16" Alum. Tube, 4" Long

1. Electrical Panel
2. Transmitter Box
3. Filter Control
4. Marker Light Switch box
5. Receiver Box
6. Rudder & Aileron Trim Knobs
7. Landing Gear Control
8. Trim Control Box
9. Elevator Trim Wheel
10. Oxygen Regulator
11. Control Box
12. Control Stick
13. Control Stick Handle
14. Armour Plating
15. Cockpit Side Lights (2)
16. Emergency Bomb Release
17. Emergency Hydraulic Pump
18. Junction Box

1. Rudder Pedals (Vacuform) 2 each
2. Rudder Pedal Frame (Resin) 2 each
3. Silver Cord, 24" Long
4. Pulleys (Resin) 2 ea.
5. Pulley Mount (Vacuform)
6. 1/8" ID Plastic Tube, 1" Long

1. Base (Vacuform)
2. Braces (Vacuform) 4 large,2 small
3. Canopy Sliding Brace (Resin)
4. Chain, 6" Long Plastic
5. 1/8" Ply 6" x 3/8"
6. 1/4 Brass Angle, 26" Pieces

1. Right Side Wall
2. Left Side Wall
3. Left Side Lower Control Box
4. Cockpit Side Braces (2)
5. Rear Wall
6. Seat
7. Dash Hood
8. Dash
9. Upper Deck Rear Former
10. Upper Deck Floor
11. Canopy Brace
12. Center Dash
13. Floor Panel
14. Head Rest
15. Top Seat Brace
16. Seat Side Braces

1. Crank Base
2. 1/16 x 3/16 Plastic x 2" Long
3. 3/16 x 2" Wooden Dowel

1. Silver Chain, 2" Long
2. 4x4 Piece of Cloth
3. 1/4" Plastic Angle 10" Long
4. 1/8 x 1/4" Plastic Tube,12" Long
5. Silver Chord, 10" Long
6. 3/32" Alum. Rod,12" Long
7. Alum. Wire for Switches
8. 6" of 1/8" Alum. Rod
9. Pins, 8 Large Pins, 1 T-Pin
10. 1/16" Alum Tubing, 4" Long
11. 1/8" Alum. Tubing 4" Long
12. 3/16" Oxygen Hose, 9" Long
13. Alum. Tube Seat Frame
14. 1x2" x .20 Alum. Sheet
15. Computer Disc
16. White Wire, 48"
17. Black Wire, 6"
18. 3/32" plywood, 6x 8"
19. Yellow Striping Tape
20. 1/4" ID Plastic Fuel Tubing 4" Long

1. Control Stick (1/4" White Plastic)
2. Control Stick Handle
3. Large Radio Box
4. Small Battery Box
5. Air Regulator
6. Trim Wheel
7. Trim Knobs (2)
8. Gun Port Cap, 3/8 Knurled Rod
9. Canopy Release Handle
10. 3/16" Knurled Rod
11. Armour Plating Bottom
12. Armour Plating Top

Vacuform Parts:

1 Dash (Inner)
2 Dash (Hood)
3  Center Lower Dash
4 Center Dash Fuel Selector
5 Right Side Wall
6 Left Side Wall
7 Right Side Upper Side Brace
8 Left Side Upper Side Brace
9 Right Side Circuit Breaker Panel
10 Cover Under Circuit Breaker Panel
11 Cover under Electrical Panel
12 Head Rest
13 Outer Dash Panel
14 Canopy Brace
15 Under Floor Fuel Guage Bracket

1 Main Body (Resin)
2 Tension Knob (Resin)
3 3/32" Aluminum Rod, 6" Long
4 Three Large Pins
One T-Pin
6 3/32" Aluminum Tube, 6" Long
7 1/8" Aluminum Tube, 3" Long

16 Control Stick
17 Control Stick Top
18 Switch Panel on Left Side
19 Armour Plating
20 Armour Plating Angle Brace
21 Electrical Panel on Right Side
22 Oxygen Regulator
23 Emergency Canopy Release Handle
24 Canopy Release Handle Bracket

1 Console Box (Vacuform)
2 Trim Knobs (2) Resin
3 Elevator Trim (Resin)
4 Two Large Pins
5 1/16x3/16" Plastic Rectangle, 3"Lg.
6 One T-Pin
7 3/32" Tube, 3" Long
8 1/4" x 1" Plastic Rod
9 3/16" x 1" Plastic Rod

1 Main Body
2 Head Rest
3 Clear Lens 2x2
4 1/64" Ply, 2x2
5 3/8 Knurled rod 1' Long
6 1/4 Plastic rod 2" Long

1 Aluminum Seat Frame
2 Seat Back (Vacuform)
3 Seat Bottom (Vacuform)
4 Seat Brace (aluminum)
5 3/32" Aluminum Rod, 6" Long
6 Seat Brackets (2) Resin

25 Two Rudder Pedals (Vacuform)
26 Two Rudder Pedal Brackets (resin)
Flare Gun Port

1 Crank Handle
2 Crank Handle Base

27 Main Body (resin)
28 Cap, 1/2" knurled Rod
29 Chain, 2" Long

1. Cockpit Floor (2)
2. Dash
3. Dash Hood
4. Cockpit Left Side Panel
5. Cockpit Right Side Panel
6. Rear Wall
7. Seat Base (3)
8. Seat Bottoms (3)
9. Pilot Seat Back
10. Gunner and Radio Operator Seat
Back (2)
11. Rear Cockpit Floor
12. Rear Cockpit Lower Piece below Floor
13. Rear Cockpit Upper Piece above Floor
14. Rear Wall of Rear Cockpit
15. Oxygen Regulator Guages (3)
16. Small Lower Right Control Panel
17. Shelf Floor

1. Base (resin)
2. 1/4" alum. Tube 4" lg
3. 7/32" Alum. Tube 6" lg.
4. Plastic Collar, 1/4 x 3/8 x 1/4 lg.
5. Knurled Rod, 5/16 dia. (Resin)
6. Gunsight Cross Bar (resin)
7. Connecting Tube (resin)
8. Handles (resin 2 pcs)
9. Elbow Junction Box (resin)
Gunner and Radio Operator Seat 10. Gunsight Reflector
11. Above Pieces for one Gunsight, Two
Gunsights Included

1. Flap Control
2. Oxygen Control Box (3)
3. Intercom Control Box (3)
4. Circuit Breaker Panel (1)
5. Switch Box (1)
6. Control Box for Gunner (1)
7. Cockpit Heater (1)
8. Left Side Electrical Panel

1. Black Chord, 3/32 x 3 ft.
2. 1/8 Plastic Rail, 3 15" pcs
3. One Roll Alum. Wire
4. Pins, 11 big, 2 small
5. 1" of 1/8" sq. white plastic
6. Alum. Tube, 1/16" dia. X 6"
7. Computer Disc
8. Guages
9. Plastic for guages
10. 1/8" Alum. Rod, 6" Long
11. 3/32" Alum. Rod, 12" Long
12. 1/4" Flex Hose, 18" Long
13. 3/16" Flex Hose, 24" Long
14. 3/16" Rod , 12 inches long

9. Control Yoke
10. Control Wheel
11. 6" of chord 1/16 dia.
12. 2" of 3/16 Alum. Tube
13. 4" of 1/14" Alum. Tube
14. 5" of 9/32" Alum. Tube
15. 1/8" plastic round rod 1" long

1. Body (1 resin)
2. Handle Top, 1/8" sq. x2" plastic
3. 3" of 14 Guage Black Wire
4. Handle Grip, 1/8x 1/16x2 Plastic

1. Main Body (resin)
2. Clear Plastic, 2x2"
3. 3/16" Round Plastic 2" Long